Manfred's TR1. Discussion Boards

Welcome, Guest. Please Login or Register.

13.05.25 at 04:27:49

Manfred's TR1. Discussion Boards › TR1 Discussion Boards › General technical TR1 discussions
(Moderator: Manfred)

Pages: 1

Rear Shock (Read 1512 times)

shalesy TR1 Board Newbie Posts: 34 Gender: Bike: TR1 - 1984	Rear Shock 18.07.21 at 20:50:44 Anyone know where I can get the bottom bush pin - 93612-99168 - from or the dimensions of it? The bush I have found at CMSL. Thanks, John
	Certain defects are necessary for the existence of individuality
	IP Logged

Kiwimanx TR1 Board Newbie Mild custom hobbyist Posts: 5 Gender: Bike: 1982 Yamaha XV1000 TR1 RH	Re: Rear Shock Reply #1 - 18.07.21 at 22:16:09 XV1000 5A8 rear shock lower bush pin M12 x 122. Just re-installing my repainted swing arm so was easy to get at. Hope this helps
	1975 Honda Goldwing GL1000 café 1982 Yamaha XV1000 TR1 RH 1984 Honda CBX750f café 1985 BMW K100 café sport 1996 BMW K1100 LT 2008 Kawasaki Vn900 classic 'Drifter'
	IP Logged

shalesy TR1 Board Newbie Posts: 34 Gender: Bike: TR1 - 1984	Re: Rear Shock Reply #2 - 18.07.21 at 22:31:18 Thanks for that Kiwi. Anything special about it? Hardened?
	Certain defects are necessary for the existence of individuality
	IP Logged

nanno TR1 Board Extraterrestrial Member Ich mags halt gern ned ganz so original... Posts: 2263 Gender: Bike: TR1, XT600, SR500-Gespann	Re: Rear Shock Reply #3 - 18.07.21 at 23:08:34 File-test didn't reveal a hardened pin at least not on my TR1(s)
	Frei ist, wer frei denkt! http://greasygreg.blogspot.co.at/
	IP Logged

shalesy TR1 Board Newbie Posts: 34 Gender: Bike: TR1 - 1984	Re: Rear Shock Reply #4 - 19.07.21 at 08:34:18 Nanno
	Certain defects are necessary for the existence of individuality
	IP Logged

nanno TR1 Board Extraterrestrial Member Ich mags halt gern ned ganz so original... Posts: 2263 Gender: Bike: TR1, XT600, SR500-Gespann	Re: Rear Shock Reply #5 - 19.07.21 at 09:40:55 I also admit knocking one up from a bit of stainless bar just to see how it goes. But this has only done a hundred km or so.
	Frei ist, wer frei denkt! http://greasygreg.blogspot.co.at/
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Rear Shock Reply #6 - 20.07.21 at 12:37:09 I too knocked one up from stainless. Mine has been on for thousands of miles with no sign of wear. Kevin
	« Last Edit: 23.07.21 at 18:47:53 by kdemery »
	IP Logged

shalesy TR1 Board Newbie Posts: 34 Gender: Bike: TR1 - 1984	Re: Rear Shock Reply #7 - 21.07.21 at 13:54:06 1m of stainless bar just arrived.
	Certain defects are necessary for the existence of individuality
	IP Logged

shalesy TR1 Board Newbie Posts: 34 Gender: Bike: TR1 - 1984	Re: Rear Shock Reply #8 - 12.10.21 at 13:28:37 Just by way of an update, the bottom bush, supplied by CMSL is NOT correct. The part number on the package was correct but it is for a smaller diameter pin. As the pin is a good "sliding fit" in the bottom bush, I returned it.
	Certain defects are necessary for the existence of individuality
	IP Logged

Pages: 1

Manfred's TR1. Discussion Boards › TR1 Discussion Boards › General technical TR1 discussions
(Moderator: Manfred)