Manfred's TR1. Discussion Boards

Welcome, Guest. Please Login or Register.

05.05.25 at 09:04:47

Manfred's TR1. Discussion Boards › TR1 Discussion Boards › Help me! I'm lost with my TR1!
(Moderator: Manfred)

Pages: 1 2

Steckachse XS 650 (Read 8517 times)

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #10 - 29.08.13 at 18:37:27 Hello If I understand this thread correctly (the translator doesn't work fully) you need the dimensions of the axle to fit XS650 hubs to the TR1 forks. Is that correct? If so please see below an extract from the original Robert Lincoln notes. A TR1 front axle is used. I followed these dimensions and it fitted well. Regards Kevin
	Front_axle.JPG Picture below may be scaled. Click link or picture for original size \| Click here for all attachments
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #11 - 29.08.13 at 18:39:00 Note You will need to use an XS650 speedo drive. Regards Kevin

	IP Logged

Bocki Ex Member	Re: Steckachse XS 650 Reply #12 - 29.08.13 at 23:34:50 oh very thanks, but I would know the dimensions of distance bushes when I use without the speedometer gear. that's my problem.
Bocki Ex Member
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #13 - 30.08.13 at 12:24:06 Hello Hendrik I don't know. I will take my wheel out over the weekend and measure it. Kevin

	IP Logged

Bocki Ex Member	Re: Steckachse XS 650 Reply #14 - 30.08.13 at 12:36:52 I would be grateful to you........
Bocki Ex Member
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #15 - 01.09.13 at 19:45:41 Hello Well i took the wheel out nd measured the spacers. I have attached a photo to show which spacers are which. In th eorder shown in the photo. Th eleft hand mpost spacer, as seen from the front of the bike is 20mm. I then have the XS650 hub. The XS650 speedo drive comes next and is 31.5mm wide. Next I have a small 17mm spacer washer which is 3.2mm wide. Note when you make up a spacer to replace the speedo drive remeber that there are tags which engage between the wheel and the speedo drive. Any spacer you make should allow for the tags which stick out beyond the bearing surface. I hope this helps. Regards Kevin 1st shows the wheel. 2nd photo shows the wheel hub with tags that engage with the speedo drive. 3rd photo shows the two spacers and speedo hub.
	image00002_001.jpg Picture below may be scaled. Click link or picture for original size \| Click here for all attachments
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #16 - 01.09.13 at 19:47:50 Hub with drive tags for speedo drive
	Image00006.jpg Picture below may be scaled. Click link or picture for original size \| Click here for all attachments
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #17 - 01.09.13 at 19:48:33 Spacer 20mm XS650 speedo drive 31.5mm Spacer washer 3.3mm
	Image00007.jpg Picture below may be scaled. Click link or picture for original size \| Click here for all attachments
	IP Logged

kdemery TR1 Board Senior Member Posts: 397 Gender: Bike: TR1 & Vincent Rapide	Re: Steckachse XS 650 Reply #18 - 01.09.13 at 19:49:22 Sorry. Spacer washer is 3.2mm

	IP Logged

Bocki Ex Member	Re: Steckachse XS 650 Reply #19 - 01.09.13 at 23:17:33 well then should tune my drawing .... many thanks
Bocki Ex Member
	IP Logged

Pages: 1 2

Manfred's TR1. Discussion Boards › TR1 Discussion Boards › Help me! I'm lost with my TR1!
(Moderator: Manfred)